Harbor Freight 1x30 sander- my favorite sharpening system
2013年2月11日 · Anyone ever used the $40 dollar harbor freight belt sander with Aluminum Oxide belts to sharpen your knives? I have tried many different sharpening systems (lansky, stones, ect), and by far, this is the best way I’ve found to sharpen …
Preferred method for sanding down handguards - M14 Forum
2024年7月9日 · I know Harbor Freight ~$89 - but I use this specific model for handguards and many other stock projects! You can move/adjust the long sander to a flat position or elevated and trim hanguards and I use this when working on XM25 stocks/custom butt pads and many other projects. M1Army
Rubber butt plate on Walnut stock - M14 Forum
2024年6月13日 · Then trace the outline of the stock with a scribing tool a icepick or sharp pointed knife will work. Remove pad then pour baby powder on it and run into the scribe mark. Wipe off excess powder. Use a bench grinder to sand down to the scribe make. A belt sander zip tied with multiple heavy ties to a saw horse will make a bench grinder.
Gas system unitizing with screws | M14 Forum
2023年7月5日 · You will need drill bits in #33, #28, a 3/8" 82 degree counter sink, a standard #3 drill bit, 6-32 tap, and a #2 Phillips screw driver. You need an alignment gauge for the gas ports. You will also need a strip of medium Crocus cloth to …
Stripper clip roll pin question. - M14 Forum
2020年3月12日 · Got it. Just needed a quality punch it seems. Got a Starrett 3/32 from Amazon and it slid right in, couple of taps and the pin eased on out. I think the Harbor Freight 3/32 was slightly oversize and wasn't fitting into the channel in the receiver. The first punch I tried, a Lowe's cheapie, was evidently made of spaghetti.
SAGE EBR Op Rod Guide Block - M14 Forum
2018年7月26日 · 82 posts · Joined 2011. #1 · Jul 26, 2018. I finally started my SAGE EBR NSG MOD 0 build. Took advantage of BULAs 4th of July sale and bought an M14 barreled receiver with a 19.25 inch GI profile barrel and a M14 parts kit. I got the trigger group and bolt assembled. When i was ready to install the Sage Op Rod Guide block.
Buffing wheel suggestions | M14 Forum
2022年1月14日 · Harbor freight with a buffing wheel - put it in my vice and manipulate the stock over the buffing pad! Buff the stock after the final coat of teak oil dries for two days, then apply 4-5 coats of Renaissance Wax by hand and buff the wax by hand. M1Army. "Speak Softly and Carry a Big M14; You Will go Far". M1Army.
7.62 Wylde equivelent reamer - M14 Forum
2013年3月3日 · Rim/Belt Thickness 0.2000 Shoulder Angle 20* Throat 1*45” 7.62 NATO Shank 0.4670 Base Diameter 0.4725 Shoulder Diameter 0.4560 Neck-1 0.3460 Neck-2/Case Mouth 0.3460 Freebore Diameter 0.3110 Pilot Diameter 0.2990 Min. Chamber Length/Base-to-Case Mouth 2.0250 Base-to-Shoulder 1.3560 Neck Length 0.3200 Freebore Length 0.1500 Rim/Belt …
Polytech / GI Bolt Conversion - M14 Forum
2021年4月9日 · I recently picked up a nice heel stamped Kengs Polytech M14S. I want to install a GI TRW bolt. The GI bolt will not close on an empty chamber. From my reading on this and various forums I should grind/file off the portion of the barrel shroud that it is hitting the front of the left bolt lug as shown in the arrow below.
UTG New Gen 4-Point Locking Deluxe M14/M1A Scope Mount...
2022年12月31日 · SADLAK M1A Scope Mount w/ Free Shipping — 3 models. Shop SADLAK M1A Scope Mount | 4.8 Star Rating on 35 Reviews for SADLAK M1A Scope Mount Best Rated + Free Shipping over $49. Thanks for the info. My wife took over the S4 shop while I was out twiddling my thumbs and went ahead and bought the UTG.