Attack angle on your cutting edge | Snow Plowing Forum
2008年2月9日 · depends on what the plow is being used for..correct me if i'm wrong but highway plows have less of an attack angle to lift the snow off the road and trow it off to the side at high speeds. I believe blizzard plows have an attack angle of 70 degrees. Its not an exact science there is a small margin for different angles.
Anyone Use Polyethylene Cutting Edges | Snow Plowing Forum
2011年10月9日 · 66 posts · Joined 2010. #6 · Sep 19, 2010. that is why we switched to cutting edge poly's blades b/c we could not scrape clean with the rubber edges on our pushers. with their poly we are cleaning the snow pack as well as the trucks with steel blades, only the poly lasts way longer than the steel. Reply Like.
Urethane or Steel Cutting Edge? - Snow Plowing Forum
2013年5月30日 · If the gravel is not crushed (no sharp edges) you could use the urethane edge. I plow unimproved mountain roads that are a mix of large flat rock, some round, with loose gravel, some sharp and dirt. I try to let the snow build up a little before plowing but that is difficult sometimes. I have an older RTII V that I have drilled out to run the ...
Poly vs Steel Cutting edge - Snow Plowing Forum
2008年12月23日 · skywagon. 262 posts · Joined 2008. #2 · Dec 23, 2008 (Edited) sdubfid;688346 said: I've done some searching and everybody is raving about the poly cutting edges. I've worn through 1 half of my steel cutting edge and I've had the plow for 6 days. Is this normal? I have it set so the pucks are ven with the blade height so it scrapes more snow off.
Poly or Rubber edges - Snow Plowing Forum
2021年8月3日 · Mark Oomkes Discussion starter. 71513 posts · Joined 2000. #5 · Aug 3, 2021. Yes. T650, gave up on the Toolcat several years ago. Anything but steel. I prefer UHMW as it scrapes better than rubber or poly. DISCLAIMER: Please do not take any of my comments as derogatory or humorous in any shape, manner or form.
RUBBER CUTTING EDGE?? | Snow Plowing Forum
2000年12月31日 · The urethane edge does not dig up frozen turf; neither does a steel edge. It still dug up turf as observed back on Dec 8 when the ground was still relatively soft. No surprises there either. FWIW the edge has over 30 hours plow time on it, not 5. I dont know where Dino arrived at that number.
Polyurethane cutting edge | Snow Plowing Forum - plowsite.com
2000年11月6日 · Snow and Ice Management. Commercial Snow Removal Polyurethane cutting edge ... Polyurethane cutting edge.
Good deal on UHMW Poly edges | Snow Plowing Forum
2011年11月9日 · Update: I got the UHMW edge installed. It was no problem to put on. Obviously it is easy to drill holes in it. I just had to get new longer bolts. I don't know how it will hold up yet. We haven't had any snow yet. Other than an inch a couple weeks ago. I only did a few of my commercials. No residentials, which is where the pull plow is going to ...
On poly cutting edge VS. steel or rubber | Snow Plowing Forum
2010年11月11日 · 41 posts · Joined 2009. #2 · Nov 11, 2010. get to your local dealer, you can get a new rubber or poly cutting edge installed for less than $150. i would go rubber. 1999 GMC K2500 HD 5.7L Long Bed. 7.5" Meyer ST. Snow Ex Mini Pro 575 w Variable Speed Controller. Toro PowerLite 98cc Snow Thrower. www.divisionlandscaping.com.
Problem with Poly cutting edge on my Boss V - Snow Plowing Forum
2011年11月10日 · 4 posts · Joined 2011. #1 · Feb 25, 2011. I bought 2 Boss V's this year and outfitted one with a poly cutting edge. The edge has pre-drilled slots. After first use the edge pushed itself all the way up the slots. Then it wore down so fast it ruined the weld on the bottom of the plow. I've read that I probably should've used a piece of steel ...